wiellagers freelander 2000 achterwiel
-
Marry huijsman
- Berichten: 12
- Lid geworden op: 20 Dec 2015, 12:04
wiellagers freelander 2000 achterwiel
hoi ik heb een freelander uit 2000 met een nieuwe motor nou ben ik de wielagers achter aan het vervangen maar ik kan er niet bij ik heb de moer er af maar verder kom ik niet ,moet ik de achter steek as eerst verwijderen of doe ik iets verkeerts als ik de wiel ophanging los wil maken druk ik de steek as naar binnen en dat is niet de bedoeling denk ik dus hoe kom ik nu bij de lagers iemand een idee graag bedankt al vast
- Erik Peters
- Berichten: 3074
- Lid geworden op: 27 Sep 2007, 18:33
- Locatie: Heino
Re: wiellagers freelander 2000 achterwiel
Helaas heb ik geen Freelander en weet niet exact hoe e.e.a. in elkaar steekt, maar ik vermoed dat er een perslager in zit. Een video over wiellagers en hun montage: https://www.youtube.com/watch?v=WyfKTBEI0T0 en ik denk dat het rond 6.00 minuten interessant wordt, aangezien dan de montage van het perslager getoond wordt.
Groet,
Erik.
Groet,
Erik.
Alle eventuele typefouten, spelfouten en grammaticale onjuistheden zijn ontstaan tijdens de verzending van dit bericht
Re: wiellagers freelander 2000 achterwiel
Weet ook niks van een Freelander, maar lijkt me dat de naaf eraf moet. Daarachter zit het lager. Op http://cat.lrparts.ru/ heb je een soort van exploded vieuw.
Edward van Vugt
Land Rover Serie IIa 1968
Land Rover Serie IIa 1968
- RobStewart
- Berichten: 2280
- Lid geworden op: 15 Mei 2011, 12:04
- Locatie: Roger Young Land Rover, Cornwall
- Contact:
Re: wiellagers freelander 2000 achterwiel
... so the book time is 3hrs for both sides
... the instructions are as follows
... my personal recommendation based on the fact that I have done the job several times (that is more than 30) ... go and pay for someone else to do it and you could pay me anything and I would still say no its a shit job and even with the special tools it's a shit job and then it just gets shittier.
Have Fun
Rob
PS make sure you put the bearing in the correct way round, if you dont and you drive it off the ramp and the ABS lamp comes on then you have the same fun over again and you get to buy a whole new bearing too ...
PPS have you any idea what 400Nm is like to achieve outside of a workshop with hand tools ?
... the instructions are as follows
... my personal recommendation based on the fact that I have done the job several times (that is more than 30) ... go and pay for someone else to do it and you could pay me anything and I would still say no its a shit job and even with the special tools it's a shit job and then it just gets shittier.
Have Fun
Rob
PS make sure you put the bearing in the correct way round, if you dont and you drive it off the ramp and the ABS lamp comes on then you have the same fun over again and you get to buy a whole new bearing too ...
PPS have you any idea what 400Nm is like to achieve outside of a workshop with hand tools ?
Aub alleen te reageren in het Nederlands
1949 1,6 Series I
1975 3,5 V8 Range Rover
1989 3,5 V8 Discovery
2010 Td4e GS Freelander 2
2008 Td4 GS Freelander 2 ... yes we now have two

1949 1,6 Series I
1975 3,5 V8 Range Rover
1989 3,5 V8 Discovery
2010 Td4e GS Freelander 2
2008 Td4 GS Freelander 2 ... yes we now have two
Wie is er online
Gebruikers op dit forum: Geen geregistreerde gebruikers en 28 gasten